Exactly How to Install a Bathtub
Exactly How to Install a Bathtub
Blog Article
Have you been in search of facts and techniques on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bathtub isn't exactly rocket science, however it does call for strong plumbing, woodworking, and often, tiling abilities. Changing an old bathtub with a new one is also a moderately challenging task. If the old bathtub is conveniently accessible, the project can move speedily; if you have to open a wall to remove the old tub and position the new bathtub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require a helper to leave the old bathtub as well as set in the new one. Ensure you have qualified on your own for the work and are comfortable attempting it. Rather than working with a contractor to take over a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Chances are you may need a professional plumber to make tube connections.
This write-up will certainly assist you set up a new bathtub in your bathroom if you have actually currently purchased a brand-new bathtub as well as don't require to alter the arrangement of your previous water supply pipes.
Your devices and also product list must comprise the following:
Planning for the Installment
To start with, the supporting frame supplied with the bath should be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the tap includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to avoid strain on the bathtub.
Fit the flexible tap adapters to the bottom of the two taps utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the water system. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be rather bothersome due to the limited access that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipes. As soon as the supply pipes have actually been gotten rid of, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming during this process. When the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the required position. The wooden boards are practical in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to ensure that the tub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the bathtub up until the spirit level checks out degree.
To mount faucets, fit the bottom of the outermost adaptable faucet adapter to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water supply and examine all joints and also new pipework for leaks and tighten them if necessary. Fill the bathtub and also check the overflow outlet and the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the maker's user's manual. Tiling and also securing around the tub must wait up until the tub has been used at the very least when as this will certainly settle it into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin making certain that the washing machines are in place in between the tap and also the sink. Safeguard the tap in place with the manufacturer given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split a stiff seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in complications with moisture and feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components as well as installations. They are offered in tubes and cartridges, as well as can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to permit the motion experienced when the bathtub is in usage. The sealant can split rather early if you do not think about this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I was thinking sharing that post was mandatory. Be sure to take the opportunity to distribute this article if you liked it. We treasure reading our article about Tools You Need to Install a New Bathtub .
Visit Site Report this page